Campbell CR200X Uživatelský manuál Strana 4
- Strana / 8
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
4
Enclosures
Applications with minimal power requirements can
use the ENC200 enclosure to house the datalogger and
the #16869 sealed rechargeable battery. is 6.7-in x
5.5-in x 3.7-in enclosure has one power connector, one
antenna connector, and ve compression ttings.
The ENC200 cannot house a barometer or a bat-
tery that is larger than the #16869. However, an
ENC10/12 or ENC12/14 enclosure is adequate for
most CR200X, CR206X, CR211X, or CR216X-based
systems. An ENC16/18 enclosure can house a
CR295X-based system.
Power Supply
Sealed rechargeable battery options for the CR200X,
CR206X, CR211X, or CR216X include the #17365
7-Ahr battery and the #16869 0.8-Ahr battery. ese
batteries should be recharged either with a solar panel
or ac wall charger. Campbell Scienti c o ers the
SP5-L 5-Watt Solar Panel that attaches directly to the
datalogger’s terminal strip, and the SP5 5-Watt Solar
Panel that plugs into the ENC200’s power connector.
AC wall charger options are the #15988 wall char-
ger that attaches directly to the datalogger’s terminal
strip, and the #16876 wall charger that plugs into the
ENC200’s power connector.
Typical power supply for a CR295X-based system
consists of a BP12 12-Ahr or BP24 24-Ahr battery
pack, CH100 or CH200 regulator, and SP10 10-Watt or
SP20 20-Watt solar panel.
Antennas and Antenna Accessories
CR206X and CR211X Antennas
14204• —0 dBd, omnidirectional ½ wave whip,
jointed, adjustable from 0° to 90°. Connects di-
rectly to the datalogger; no antenna cable needed.
15970• —1 dBd, dipole supplied with window/
wall mount and a 10-foot RG-174 cable for con-
necting to the datalogger.
14221• —3 dBd, omnidirectional with mounts;
requires an antenna cable to connect to the
datalogger.
14201• —9 dBd, Yagi with mounts; requires an
antenna cable to connect to the datalogger.
CR216X Antennas
16005• —0 dBd, ½ wave whip articulating.
Connects directly to the datalogger; no antenna
cable needed.
16755• —13 dBd, Yagi with mounts; requires an
antenna cable to connect to the datalogger.
Antenna Cables
COAXRPSMA-L• —low-loss RG58 cable that is
recommended for lengths less than 10 feet.
COAXNTN-L• —low-loss RG8 cable that is recom-
mended for lengths greater than 10 feet; requires a
14962 or 16982 surge protector kit.
Antenna Surge Protector Kits
14462• —Surge Protector Kit for the CR206X or
CR211X; requires the COAXNTN-L cable.
16982• —Surge Protector Kit for CR216X; requires
the COAXNTN-L cable.
At left, an ENC200 en-
closure houses a CR206
datalogger and a 16869
battery. This very small
enclosure has connec-
tors for the SP5 solar
panel and an antenna.
The SP5 and SP5-L
capture solar energy
via a 72-square inch
surface area. These
solar panels are suit-
able for sites with good
exposure to sunlight
and systems with low
power requirements.
14221
15970
14201
Above are antennas used with the CR206X and CR211X data-
loggers. The 14201 Yagi antenna is intended for longer trans-
mission distances.
Související produkty a manuály pro Měření, testování a kontrola Campbell CR200X
Měření, testování a kontrola Campbell CS100 Manuál
(24 stránky)
(24 stránky)
Měření, testování a kontrola Campbell AM16 Manuál
(52 stránky)
(52 stránky)
Měření, testování a kontrola Campbell HC2S3 Manuál
(36 stránky)
(36 stránky)
Měření, testování a kontrola Campbell CS451 Manuál
(36 stránky)
(36 stránky)
Bissell Steam Shot 16Q1E SERIES Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Dampfreiniger Bissell Steam Shot 16Q1E SERIES.
Wir stellen 1 PDF-Handbücher Bissell Steam Shot 16Q1E SERIES zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Betriebsanweisung
Komentáře k této Příručce