Enclosures
Applications with minimal power requirements can use the ENC200
enclosure to house the datalogger and the #16869 sealed recharge-
able battery. This very small enclosure has one power connector, one
antenna connector, and ve compression ttings.
The ENC200 cannot house a barometer or a battery that is larger
than the #16869. However, an ENC10/12 or ENC12/14 enclosure is
adequate for most CR200X, CR206X, CR211X, or CR216X-based sys-
tems. An ENC16/18, ENC24/30, or ENC24/30S enclosure can house a
CR295X-based system.
Power Supply
Sealed rechargeable battery options for the CR200X, CR206X,
CR211X, or CR216X include the BP7 7 Ah battery and the #16869
0.8 Ah battery. These batteries should be recharged either with a
solar panel or ac wall charger. Campbell Scientic oers the SP5-L
5 W Solar Panel that attaches directly to the datalogger’s terminal
strip, and the SP5 5 W Solar Panel that plugs into the ENC200’s power
connector. AC wall charger options are the #15988 wall charger that
attaches directly to the datalogger’s terminal strip, and the #16876
wall charger that plugs into the ENC200’s power connector.
Typical power supply for a CR295X-based system consists of a BP12
12 Ah or BP24 24 Ah battery pack, CH100 or CH200 regulator, and
SP10 10 W or SP20 20 W solar panel.
The ENC200
is a very small
enclosure and
has the dimen-
sions of 17 cm
by 14 cm by
9.4 cm (6.7 in
by 5.5 in by
3.7 in).
Antennas and Antenna Accessories
CR206X and CR211X Antennas
14204—0 dBd, omnidirectional ½ wave whip, jointed, adjustable
from 0° to 90°. Connects directly to the datalogger; no antenna
cable needed.
15970—1 dBd, dipole supplied with window/wall mount and a
10 foot RG-174 cable for connecting to the datalogger.
14221—3 dBd, omnidirectional with mounts; requires an antenna
cable to connect to the datalogger.
14201—9 dBd, Yagi with mounts; requires an antenna cable to
connect to the datalogger.
CR216X Antenna
16005—0 dBd, ½ wave whip articulating. Connects directly to the
datalogger; no antenna cable needed.
30411—5.8 dBd (8 dBi), omnidirectional that uses the 13906
mounting hardware; requires an antenna cable to connect to the
datalogger.
16755—13 dBd, Yagi with mounts; requires an antenna cable to
connect to the datalogger.
Antenna Cables
COAXRPSMA-L—low-loss RG58 cable that is recommended for
lengths less than 3 m (10 ft).
COAXNTN-L—low-loss RG8 cable that is recommended for
lengths greater than 3 m (10 ft); requires a 14962 or 16982 surge
protector kit.
Antenna Surge Protector Kits
14462—Surge Protector Kit for the CR206X or CR211X; requires
the COAXNTN-L coaxial cable.
16982—Surge Protector Kit for CR216X; requires the COAXNTN-L
coaxial cable.
The SP5 and SP5-L
capture solar energy
via a 72-square inch
surface area. These
solar panels are suit-
able for sites with good
exposure to sunlight
and systems with low
power requirements.
Above are antennas used with the CR206X and CR211X dataloggers. The
14201 Yagi antenna is intended for longer transmission distances.
15970
14201
14221
(34 stránky)
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce