Campbell CDM-VW300 Series Manuál stáhnout pdf (Strana 100)

Appendix G. CRBasic Program Library

CDM_VW300Dynamic(CPI_ADDR5,Freq5(),Diag5())

CDM_VW300Dynamic(CPI_ADDR6,Freq6(),Diag6())

CallTable dynamic

If TimeIntoInterval (0,1,Sec) Then

CDM_VW300Static(CPI_ADDR1,StaticFreq1(),Therm1(),DynStdDev1()) 'Get static readings

CDM_VW300Static(CPI_ADDR2,StaticFreq2(),Therm2(),DynStdDev2())

CDM_VW300Static(CPI_ADDR3,StaticFreq3(),Therm3(),DynStdDev3())

CDM_VW300Static(CPI_ADDR4,StaticFreq4(),Therm4(),DynStdDev4())

CDM_VW300Static(CPI_ADDR5,StaticFreq5(),Therm5(),DynStdDev5())

CDM_VW300Static(CPI_ADDR6,StaticFreq6(),Therm6(),DynStdDev6())

CallTable static

EndIf

NextScan

EndProg

G.1.5 50 Hz Measurement Example — One CDM-VW300, Two

Channels

'===50Hz-1Device2Ch_4-25-13.CR3===

'CR3000 datalogger

'CDM-VW300 vibrating-wire analyzer

'Program to read 50-Hz dynamic data from one CDM-VW300 analyzer measuring two channels

'IMPORTANT -- Ensure that the CPI address coded on the following line matches the address

'reported for the attached analyzer in the DevConfig or DVWTool software.

Const CPI_ADDR = 1 '<<<<<<<<<<<<<<SET CPI ADDRESS HERE

Public Freq(2) 'dynamic frequencies

Public Diag(2) As Long 'diagnostic code

Public StaticFreq(2) 'Static (1Hz output) frequencies

Public Therm(2) 'Thermistor readings

'Standard Deviation of the dynamic readings that occurred during the latest one-second interval

Public DynStdDev(2)

'The following arrays are used to configure the CDM-VW300 series device. Refer to the

'CDM_VW300Config instruction used below.

' CH1 CH2

' --- ---

'Set to true (Enabled=1, Disabled=0) only those channels which have sensors connected

Dim Enable(2) As Long = { 1, 1}

'Specify the target/desired resonant amplitude at which the sensor will be maintained

'via excitation, given in volts. This should be in the range 0.010 to 0.001

Dim Max_AMP(2) = { 0.002, 0.002}

'Low Frequency Boundary (sensor frequency should never fall below

'this value regardless of environmental changes)

Dim F_Low(2) = { 300, 300}

'High Frequency Boundary (sensor frequency should never exceed

'this value regardless of environmental changes)

Dim F_High(2) = { 6000, 6000}

'Output Format - Hz vs. Hz^2 :: Value of 0 – measured frequency is given in units of Hz,

'Value of 1 – measured frequency is squared and given in units of Hz^2

Dim OutForm(2) As Long = { 0, 0}

'Multiplier (factor) to be applied to sensor output frequency

Dim Mult(2) = { 1.0, 1.0}

'Offset (shift) to be applied to sensor output frequency

Dim Off(2) = { 0.0, 0.0}

'Steinhart-Hart coefficients [A,B,C] for converting thermistor ohms to

'temperature in Celsius. Specifying zeroes for A,B,C results in a reading in Ohms.

Dim SteinA(2) = { 0.0, 0.0}

Dim SteinB(2) = { 0.0, 0.0}

Dim SteinC(2) = { 0.0, 0.0}

'Rainflow configuration (not used in this program,

'but required as configuration arguments)

Dim RFMB(2) As Long = { 20, 20}

Dim RFAB(2) As Long = { 20, 20}

Dim RFLL(2) = { 400.0, 400.0}

Dim RFHL(2) = {4000.0,4000.0}

G-8

1 2 ... 95 96 97 98 99 100 101 102 103 104 105 ... 121 122

Komentáře k této Příručce

Žádné komentáře

Campbell CDM-VW300 Series Manuál Strana 100

Komentáře k této Příručce

Související produkty a manuály pro Měření, testování a kontrola Campbell CDM-VW300 Series